Homemade desk for a child. Desk drawing. Assembly diagram and detailed description of the home desk. Wooden desk

DIY children's desk, drawings, description and order of its assembly. The proposed model will be able to serve your child for a long time until high school.

If your child has gone to school, then you are faced with the acute question of choosing a desktop or desk for his normal development. Correct posture and reducing eye strain require an individual approach when choosing a workplace that can adapt to the growth of each student.

Side view (maximum table extension)

Side view (minimum table extension with table top rotation)

• adjust table height from 570 to 720 (mm), adjustment step is 50 (mm)
• adjust the table tilt angle from 0° to 90° (the maximum angle is set theoretically), the adjustment step is 5°

Components of a children's desk:

• base
• table top lifting mechanism
• table top

BASE

We will make it from planed boards. From the inside of the guide board, at the end we mill a groove measuring 10x10 (mm). The sharp edges of the parts are rounded. We fasten the parts of the legs together using:

• threaded rods GOST 22042-76;
• enlarged washers GOST 6958-78;
• wing nuts GOST 3032-76

for M8 thread.

We attach the top shelf and footrest to the legs with wood screws

or confirmations.

LIFTING MECHANISM

We will make it from planed boards. From the outer sides of the guide board, at the end we mill grooves along the edges measuring 10x10 (mm). We drill through holes with a diameter of 20 (mm) in the center.

TABLETOP

We will make it from laminated wood or plywood.

We will make the rotating mechanism from sheet metal 2 (mm) thick and attach it to the tabletop with wood screws. Alternatively, it can be made from wooden blocks.

Assembly order:

1. We insert the lifting mechanism into the grooves of the base.

2. Secure the tabletop to the lifting mechanism using pins, washers and M8 nuts.

DIY children's desk assembled. Using the proposed concept for designing and constructing a structure, you can modify and supplement the model yourself with various shelves, pencil cases and glasses for stationery.

Types of transformers

Furniture that most often acts as a transformer:

A few examples of transformable tables:

Transformable coffee table

Computer desk-transformer

Important! When choosing a transformer, special attention should be paid to the safety of the product in order to eliminate any possibility of injury during assembly and disassembly of the structure. Sharp edges and protruding metal elements are not allowed.

What can you make a transforming table from?

Wood The most advantageous and simplest to make are tables made of wood. For this, simple solid wood and sheet wood panels (plywood, chipboard, MDF, fiberboard) are used. Plastic Possible for a transforming table, but not a very aesthetic option. Metal Tables are strong and durable, have various decor options, and are made of hollow structures. Glass More complex An option would be to use tempered glass to make transformable tables. Such tables are aesthetically pleasing, safe and have an original appearance.

To make a small chest of drawers (4 drawers), you need the following:

Materials and accessories

pull handles for all drawers (including two false ones) - 6 pieces; furniture wheels - 8 pieces; supports for wheels - 8 pieces; card hinges - 4 pieces; hinges and hinges for the table top; ball guides (400 - 2 sets, 450 - 4 sets); wooden dark-colored slabs for the table top, external side legs (on wheels), internal side legs, the middle wall (between the drawers), the bottom of the chest of drawers, the walls of the drawers and 2 long walls along which the upper false drawers will slide to the sides; light-colored wood slabs for the front of the drawers (+ 4 fake drawers on both sides) and the back of the chest of drawers. The length of the back wall is equal to the length of two drawers. The rest of the space on both sides of the chest is occupied by a long wall along which false drawers move; a thin piece of wood for the bottom of all the drawers.

pencil, square, tape measure; electric jigsaw or hacksaw; screwdriver or screwdriver; hexagons; drill with various attachments (including a 15 mm Faustner cutter); minifixes (for eccentric couplers) - 40–50 pieces; Euro-confirmed screws - 50–60 pieces; self-tapping screws (14 mm – 20 pieces, 30 mm – 50 pieces);

Stages of work

Step 1. We draw out and cut out all the details of the future chest of drawers.

Step 2. We draw and attach retractable ball guides (400) on the side walls. On the middle wall we screw the guides on both sides.

Step 3. Screw the middle wall exactly to the middle of the bottom of the chest.

Step 4. We fasten the side internal walls, the back wall and the bottom of the chest.

Step 5. We assemble all the walls of the drawers, screw the handles-brackets to the front sides (including false ones).

Step 6. We attach 2 balls from the guides (on which our drawers will roll) to the inner (which will be inside the chest of drawers) two corners of all drawers.

Step 7. Screw the guides (450) onto the wall for the false drawers and onto the back of the false drawers. We attach the long walls to the side inner walls.

Step 8. Screw the furniture wheels to the bottom of the chest of drawers and to the side outer legs.

Step 9. Attach the outer side of the false drawers to the outer legs of the chest of drawers and push them into the folded position (place them next to the functional drawers).

Step 10. We proceed to the tabletop. We fasten the three parts together using hinges.

For a dining table, this design is quite complex. Most often, a chest of drawers is used when it is not possible to purchase a kitchen or dining table or when making a huge transforming table (more than 2 meters long).

The second version of the chest of drawers differs not only in size (700 x 900 cm when folded, 2100 x 900 cm when unfolded) and the number of drawers, but also in the transformation mechanism.

The inner side walls are maximally folded out to the distance of the length of the false drawers.

The tabletop, when unfolded, consists of 3 parts - left, middle and right. When folded, the left side rests on the middle one.

The tabletop rotates 90 degrees. The right part is lowered onto the back wall of the chest of drawers (hangs parallel), and the parts stacked on top of each other form the top surface of the chest of drawers.

Wheels are attached to make our chest of drawers easy to move, but they are not required. When the table top is rotated into working condition, it fits into positioning pins, which completely prevent its further rotation.

An interesting idea for a portable folding transforming table - an ironing board built into a closet - is presented in this video:

The coffee-dining option can be found most often, because the number of friends and acquaintances who come to visit increases over the years, but the living space does not.

The transformable dining table is unnoticeable and does not detract from valuable space.

On ordinary days it plays the role of a coffee table, and on holidays it turns into a real dining table. In order to seat 5-7 people, a few simple manipulations are enough. This is suitable ergonomic furniture for a studio apartment, when the entire space is combined into one.

When creating a coffee table - a workplace, a different type of tabletop is used. There is no need for it to unfold completely or change shape.

This version of the transformable table turns into a desk, taking on the required height. Additionally, the furniture is equipped with drawers to store office supplies. Depending on the fastening system, the table can be given several positions.

Models with smooth adjustment mechanisms are more convenient to use. With their help, you can organize a workplace in any corner of the apartment.

The table storage system has an original design. It consists of two or three drawers and a tabletop. The table opens by rotating around its axis.

Table frame

The duration of operation depends on its strength. Frames come in different materials:

wooden; metal; with plastic parts.

Structures made of metal and wood are considered the most reliable.

They withstand repeated unfolding and folding cycles well. Frames with plastic components are cheaper, but do not withstand long-term use. But if the table is rarely transformed, this option can be considered.

They serve as a support, so they must withstand a large load, which increases when the table is unfolded.

Wooden supports also cope well with the load. This option is suitable for classic interiors.

Additionally, you should familiarize yourself with the types of countertops. The appearance of the product depends on the material from which the top is made.

Project cost:

Transformation mechanism – from 3 thousand rubles. Chipboard panels for table tops and legs – from 500 rubles. Fasteners – from 50 rubles. Set of screws and self-tapping screws – from 200 rubles.

It’s possible to make a folding table for $100.

Manufacturing consists of several stages:

Selecting a folding mechanism. Creating a project. Cutting out parts from a chipboard panel. Initial fitting of parts. Installing the frame. Installing table supports. Installing the tabletop.

To make a high-quality transforming table, it is better to create drawings in special computer programs. They not only draw a layout of the future furniture, but also calculate how much materials are needed and create a cutting map. The programs are quite simple to manage, so creating a project will take one or two days.

The number of parts and their sizes can be ordered at the same store where chipboard panels are sold. The cut planks only need to be connected with bolts, after which the transformation mechanism is installed. For smooth installation, it is necessary to make markings with a pencil before drilling holes for the screws.

The finished table will be no different from store exhibits if you select a high-quality transformation mechanism and materials for the frame. You should choose this kind of furniture if you don’t know how to create a functional design for a one-room apartment for a family with a child. When folded, the table will occupy a minimum of space, leaving room for children's games.

Sources:

• 6sotok-dom.com
• novamett.ru
• usamodelkina.ru
• www.weareart.ru

There are no similar posts, but there are more interesting ones.

We make a table for a child with our own hands

Taking into account the fact that the baby is growing up and has new needs, you need to carefully consider every piece of furniture that is in the children's room. The children's table is no exception. After all, your child will continue to explore the world around him, draw, sculpt, read and make various crafts.

Materials for work

If you decide to make this piece of furniture yourself, then you will need the following tools and materials:

• Solid wood sheet 60x40 centimeters;
• Beams for the frame 4 pcs.;
• Legs with a section of 4x4 centimeters 4 pcs.;
• Electric drill;
• End mill set;
• Clamp;
• Hammer;
• Wood hacksaw;
• Carpenter's knife;
• Sandpaper;
• Furniture varnish;
• Wood glue;
• Ruler;
• Furniture pins.

Important! If you have an old table, then you can use its parts to make a children's table with your own hands.

Before starting work, it is very important to determine the height of the future table. The most comfortable height is considered to be the one at which your child sits with a straight back, placing his elbow on the tabletop and easily touching his temple with his finger.

Important! In order to choose the desired table height as correctly as possible, you can use special tables that indicate the recommended standards for the manufacture of tables and chairs for children of different ages.

Work execution algorithm

When creating a children's table with your own hands, you can take ready-made drawings and diagrams. You can find them on construction sites or forums.

We offer you a general scheme for completing the work:

• Taking into account the height, saw off the legs. If they taper towards the bottom, then you can file them. This must be done in such a way that the future table is strong enough and stable.
• The prepared legs are attached to the elements of the load-bearing frame using end mills. During assembly, it is necessary to mark the locations for the grooves, and then combine the paired elements.
• Next, in the marked place you need to drill a non-through hole.

Important! The depth of the hole should be one third of the thickness of the workpiece, and the diameter should be the thickness of the future groove.

• The leg blanks must be clamped one by one in a clamp and the wood must be selected as much as possible using an end mill. This must be done carefully until you get a smooth groove of the desired size. As a result, you will have 8 grooves on 4 legs.
• Using a ruler, you need to measure the dimensions of the groove and make appropriate markings on the bars for the load-bearing frame.
• Using a carpenter's knife and a hacksaw, you need to adjust the ends of the power frame, while creating “tenons” that will easily fit into the grooves of the legs.
• At the end, a test assembly of all elements should be done.

Important! During the check assembly, you have the opportunity to make changes and adjustments to ensure that the table does not become unstable.

• The final assembly must be carried out similarly to the control one, only pre-coating the fastening points with special furniture glue.
• After everything has dried, you should secure the tabletop. To do this, you need to drill a hole in the center of the legs for a furniture pin. And on the back side of the tabletop there are blind holes.
• Coat the pins with glue and connect them into a single structure.
• The finished table must be sanded using fine sandpaper and covered with several layers of varnish.

Table with lifting lid

Once you have made a simple model of a children's table, it is ready for use. But if you want to make a more functional option, we suggest you equip it with a lid. Thus, the child will have additional space to store his stationery and other small items.

To make such a table:

• Take a wooden tabletop. Its dimensions should be 90x45 centimeters.
• You need to build a frame from bars measuring 5x5 centimeters.
• Take two pieces of length 8 and 4 centimeters. Fasten them together with nails.
• Insert another piece in the middle.
• The tabletop must be attached to the front of the frame using hinge-type furniture hinges.

Important! You can replace furniture hinges with regular door hinges.

• To create a lifting and adjusting mechanism, it is necessary to fix bars measuring 20 and 40 centimeters in a vertical position on the lid. They should be placed on the opposite side.
• In order for the lid to be fixed in different positions, it is necessary to nail 2-4 furniture hooks to the bars. Next, insert one bolt at a time into the base of the frame so that they partially protrude.
• All parts are processed with sandpaper and varnished.

We make a folding wooden table for children with our own hands

To create such a table model you will need the following materials:

• 4 boards measuring 6x2 centimeters and lengths 72 and 32 centimeters;
• Tabletop made of 2 parts;
• Wood glue;
• Electric drill;
• Furniture pins;
• Sandpaper;
• Dowels.

Important! This model does not take up much space and is suitable for small apartments.

The sequence of manufacturing a folding wooden table is as follows:

• Make 2 frames from the boards. They will “play” the role of legs.
• Using a stencil, drill holes for future fastening in the end sections of the boards.

Important! It is necessary that the lower crossbar of the frames be raised above the floor by 5 centimeters.

• The parts should be connected into frames with pins.
• Pour wood glue into the hole and connect the parts into frames. Fasten them together with loops.
• Drill a hole in the wall for the dowel.
• Attach the first part of the tabletop to the wall. A vertical folding frame must be placed under it.
• The second part of the tabletop needs to be attached with hinges to the first and laid out on top of the support frame.

Important! At any time you can lift the second part of the tabletop and fold the frames. Then the movable element of the tabletop is lowered, and the table will take up less space.

We make a children's table from furniture board with our own hands

This model is very simple and consists of a table top and legs.

Important! To make the legs, you can use bars measuring 4x4 centimeters.

The tabletop will be a furniture panel measuring 40x80 centimeters. This is already a whole preparation. In order to attach future table legs to the tabletop:

• You mark up future auxiliary elements.
• You need to make an indent of about 5-6 centimeters from the end of the tabletop.
• From the block you make blanks of the required size by sawing.
• Using wood glue and self-tapping screws, connect the bars according to the markings.
• We attach the finished legs to the tabletop using the same pattern.

Important! To ensure that the self-tapping screw that secures the leg does not “break through” the wood, it is necessary to install a metal corner.

• The finished product is opened with varnish.

Making a table out of cardboard

If you don't like working with wood, you can make a table out of cardboard. For this you will need:

• Box for furniture or household appliances;
• Cardboard tubes - they remain after the foil or cling film runs out;
• Stationery knife;
• Glue.

Operating procedure:

• Cut the box.
• Measure 5 pieces with rounded edges and a size of 55x35 centimeters.
• On 4 parts, make circle marks taking into account the diameter of the tubes. Cut them out.
• Fasten these elements together.

Important! In order for the glue to “grab” well, the workpiece must be pressed down with a press and left until completely dry.

• Try on the tubes to the workpiece. They should fit fairly tightly, so adjust the hole if necessary.
• Glue the 5th part to the workpiece. Place it under the press again.
• Spread the edges of the tubes with glue and glue them to the finished tabletop. Leave until completely dry.

Important! Decorate with self-adhesive paper and various applications.

Making a children's high chair

It is very important to make a set of table and chair at once. Such a set will not only please your baby, but will also be functional, which is important for a loving parent. We have already told you how to make a children’s table, but for the high chair you will need the following tools and materials:

• Solid wood;

Important! It is best to use beech, birch or pine. They are quite hard, but easy to process.

• Bars 2x2 or 5x5 centimeters;
• Boards 2.5 centimeters thick;
• Furniture board - for this you can use a sheet of plywood or chipboard;
• Dowels;
• Wood hacksaw;
• Screwdriver;
• Sandpaper or sanding machine;
• Hammer;
• Brushes;
• Varnish or paint.

Important! Before you start making a high chair, you need to make sure that you have taken the measurements correctly. If not, then you need to increase or decrease them proportionally, since the stability of the future product depends entirely on the ratio of height and width.

Making a drawing

In order for the baby to be not only comfortable and comfortable, but at the same time to develop correct posture, it is necessary to make a table that will fully correspond to the physical parameters of the child. You can measure it as follows:

1. Measure the distance from the bend of your knee to your heel. This parameter shows you the seat height of the future chair.
2. Next, for a test, you should sit the baby on some object that is equal to the height of the chair.
3. In this position, measure the distance between the floor surface and the child’s elbow. This will be the height of your table.

Important! Taking into account the fact that children grow very quickly and in order for the future table to last for several years, you should add a few centimeters to the current height parameter.

As for drawings and diagrams, you can find them on the Internet. But it’s best to make the drawings yourself, since you will be making a high chair taking into account the individual parameters of your baby.

Important! If you doubt the correctness of the drawing, you need to test it by making a cardboard model of the high chair.

Selection of fasteners

It is best to use dowels to secure a child's highchair. The advantage is that they can also be made from wood.

Manufacturing of parts

Before starting work, it is better to leave the wood for a day in a dry room to dry. Further:

• In order to make the legs of the future product, it is necessary to cut the bars into several pieces of the required size and sand them with sandpaper.
• The upper and lower crossbars are made using the same pattern of bars as the legs.
• To make crossbars, it is necessary to cut the bars on a flat surface in a vice. This is necessary to ensure that the cutting angle is 90 degrees.
• Curves should be cut from the board.

Important! During cutting, it is necessary that the wood fibers are perpendicular to the bend angle.

• Cut a seat out of wood.

Assembling the product:

1. We make holes in the parts of the future chair for dowels. They must first be made with a drill with a small diameter (up to 6 mm), and then expanded with a chisel.
2. We attach the parts with wood glue.
3. In order for the fastening to be as strong as possible, all elements must be placed on a dowel, and then secured with a clamp and left for a day.

Chair finishing

It can be produced using water-based varnish or acrylic paint. As for the back and seat, they can be made of foam rubber with a cover made of colored and durable fabric.

In order to make a children's table and chair with your own hands, you will need to spend a certain amount of time and physical effort. But as a result, you will receive furniture that is made with love and is ideal for your child. Using the above tips and recommendations, you will do everything right, and the finished product will delight you and your baby!

As the child grows up, new needs appear. In a children's room, every piece of furniture should be thought out to the smallest detail. There comes a time when the baby needs a children's table at which he will play, draw, eat, and learn new knowledge and skills. Of course, the easiest way is to purchase the necessary furniture attribute in the store, but it’s so nice to do something for your child yourself. In addition, only by making the table yourself can you adjust it exactly to the child’s size. Therefore, many parents are faced with the question: how to make a children’s table with their own hands?

Tools and materials for work

When choosing raw materials for a children's table, the first thing you need to be guided by is that it is completely safe. It is best to make a table with your own hands from wood, as it is a completely environmentally friendly material that will not harm the baby’s health. When starting to prepare the material, you need to understand that it will be very difficult to make a completely children’s table with your own hands, since this requires a complex tool. It is best to develop a design and order the necessary parts from a carpentry workshop.

To make a children's table from wood you will need the following materials:

1. Directly wooden tabletop. Regarding the size, it is necessary to rely on the age of the child.
2. Wooden legs for a table. Remember that the height of the table depends on their size.
3. Blanks that will serve as support bars for the table frame.
4. As for the tools, the list may vary depending on the characteristics of the material and the design of the future table.

As a rule, a standard set of tools for making a wooden table with your own hands includes:

1. Drill with various attachments.
2. Hacksaw.
3. Carpenter's knife.
4. Hammer.
5. Measuring tape.
6. Sandpaper.
7. Adhesive substance.

For our granddaughter Mashenka, my son-in-law and I made an age-appropriate small school desk with our own hands and a comfortable chair where you can look through picture books, draw, sculpt from plasticine, or lay out toys.

Required: 50 cm piano hinge confirmations self-tapping screws metal corners cutting a pine furniture board (for a desk, see diagram 1, for a chair, see diagram 2).

DIY drawings of a children's desk

DIY school desk assembly

To ensure that all wooden parts were very smooth, we treated them with sandpaper: first coarse P40, then medium P120 and finer P220. All sharp corners were rounded with a jigsaw. Semicircular grooves were cut out in the legs so that a child, sitting at a desk, could comfortably stand up and turn right and left without resting his knees.

The legs were connected to the bottom of the box using confirm mats and a screwdriver into pre-drilled holes, lowering the bottom 8 cm below the edge of the legs (Diagram 3). Then we fixed the front wall of the box so that its top edge was flush with the legs, forming a smooth box. We attached the back wall of the desk to them with screws so that it protruded a couple of centimeters above the top edge of the legs.

The tabletop was attached using a piano hinge (photo 1) to the back wall of the desk so that it could rise and fall freely and, resting on the legs, formed a flat horizontal surface. This created a shallow drawer under the tabletop for storing albums, coloring books, pencils and other small items.

By the way
The protruding edge of the back wall of the desk prevents pencils and felt-tip pens left on the tabletop from rolling off and falling to the floor when the lid is raised (photo 2).

Assembling a chair for a set with a desk

The legs were secured at an angle to the seat using a trapezoidal support board, which was inserted in the middle between them (Diagram 4). All parts at the joints were secured with metal furniture corners to strengthen the connection (photo 3). The back was attached in the same way (photo 4). For stability, semicircular recesses were cut out on the legs in the supporting part. A groove for the backrest was previously cut out in the seat (photo 5). The latter was rounded off at the top and a heart-shaped hole was cut to make the chair easier to carry.

The furniture was varnished in two layers so that it could be easily washed from paints and spilled liquids.

On a note
To cut out the heart, we first drew it with a pencil on the back, then drilled holes along the inner contour with a drill and connected them using a jigsaw.

A growing desk with your own hands, drawings, diagrams and functional dimensions of the table that can ensure the normal and healthy development of the child during classes.

The requirements for children's tables are regulated by GOST 11015-93 “Student's tables”. Based on the specified GOST, they are produced in six numbers and have their own color marking depending on the average height of the student.

The model described in this article allows you to adjust the desk according to two functional sizes to suit the average student height from 105 to 180 (cm):

• along the height of the working plane from 460 to 760 (mm) (∆h = h1 – h = 300) with an interval of 50 (mm)
• by the angle of rotation of the working plane from 0 to 16° (∆φ = φ1 – φ = 16) (four positions 7, 10, 13.16°)

The presented model consists of three assembly units:

1. Tabletop.
2. Movable stands.
3. Fixed stands.

1. TABLETOP

The size of the working plane is 500x700x20 (mm). The desk cover (1) is installed horizontally or fixed at an angle of 7, 10, 13 or 16°. Two plates are welded to a square pipe (2) 15x1.5 (mm): fastening the rotary axis (3); fixing the angle of rotation of the tabletop (4). The tube (2) is attached to the tabletop with four screws (6). The end plane is closed with a decorative plug (5). The tabletop has two recesses 220x20x5 (mm) for pencils, pens and other accessories.

2. MOVABLE STANDS

The structure is welded from metal pipes: square (3) fifteen; rectangular (6) size 35x15x2.5 (mm). To increase the rigidity of the structure, a plate (4) in the form of a right triangle with sides of 20 and 50 (mm) is welded to the corner joints. A wooden shelf (1) measuring 700 x 107 x 20 (mm) with a stop (2) is attached to the pipes. The end plane of the pipe is closed with a decorative plug (5).

3. FIXED STANDS

Welded from rectangular pipes (1) 40x2x2.5 (mm). By analogy with movable jays, a plate (3) is welded to the corner joints. The end is closed with a decorative plug (3).

The figure shows desks with minimum and maximum size changes.

Like a desk, which is the main part of the interior of any educational institution. Also, a desk can be put to good use at home, which is why it was decided to make a desk with your own hands for children. In this article I will tell you how the author made an age-appropriate small desk with his own hands and a comfortable chair, which will allow you to conveniently look through picture books, draw, sculpt from plasticine or lay out toys. Before manufacturing, we need to decide on the materials needed for this.

In order to assemble this homemade product, we will need:
*Piano hinges are 50 cm long.
*Con firms.
*Screws.
*Sandpaper.
*Metal corners.
*Cutting a furniture panel from pine, for a desk according to scheme 1, and for a chair according to scheme number 2.

Now all the materials are ready.

You will also need tools:
*Jigsaw.
*Screwdriver.
*Sanding machine to facilitate sanding work.
And this is what the drawing of our future desk looks like, since making parts with dimensions taken from your head will not only be incorrect, but also inaccurate.

Step one.
First of all, you need to assemble the desk, and only then the chair, so we gradually begin the exciting assembly process. As usual, all wooden parts should have the least roughness, which in other words simply be encrypted. It is best to grind on a grinding machine or using a sander, but if you don’t have one, you can use regular sandpaper. It should be processed with sandpaper of first coarse grit P40, then medium P120 and finer P220. We correct sharp corners using a jigsaw, thereby rounding them. After sanding, you need to cut semicircular grooves in the legs, this is done so that the child who will sit at the desk does not experience discomfort, and also so that when turning to the sides, the knees do not rest.

Step two.
Now you need to attach the legs to the bottom of the box, we do this using confirmation mats, it is better to screw them with a screwdriver into the holes that need to be made in advance, the diameter of which is slightly smaller. We lower the bottom 8 cm lower than the edge of each of the legs, as shown in the figure according to diagram 3. Then we fix the front wall of the box, taking into account that its upper edge should be level with the legs, so that the box is almost perfect and smooth. Armed with a screwdriver, we attach the back wall of the desk to them with screws; the resulting protrusion should be several centimeters higher than the edges of the legs themselves.

Step three.
A desk without a tabletop is not a desk, so we will now attach it, but for this we will need a piano hinge, it must be attached so that its free movement can allow the tabletop to be raised and lowered without any difficulties or sticking, and also so that it the surface had a flat surface when closing for better contact and evenness. The result is a medium-sized drawer under the tabletop, where you can store things such as albums, coloring books, accessories and many different little things.

It is also worth considering that the protruding edge of the back wall of the desk prevents the pen and the like from rolling and falling on the floor, which can be left on the tabletop without fear that the pen will roll somewhere when the lid is lifted, as in photo 2.

Step four.
This is how we got to the point of creating a chair, we also make it from wood, after which we fix its legs at an angle to the seat, which we fasten with the help of a trapezoidal support board, which in due course needs to be inserted in the middle between them, as shown in diagram 4. In order to to strengthen the structure, knowing that children love to swing on a chair, all its parts at the joints must be secured using metal corners that can be borrowed from furniture, see photo 3. We also attach the backrest, as shown in photo 4. You can increase stability by cutting There are semicircular recesses on the legs in the supporting part. We prematurely cut out a groove for the backrest in the seat, which is shown in photo 5. The last part was rounded off in the upper part and a heart-shaped hole was cut so the chair is easier to carry; this shape is easiest to cut using a jigsaw according to a pre-drawn pattern.

Any student class, from the youngest to the graduate, required place to study lessons.

Desk for schoolchildren should be functional, convenient and uncluttered. Most often chosen for children wooden desks.

Today, when from the first grade students work with computer, There should be room on the table for it too.

Manufacturing DIY school table - significant saving for the family budget. You can decorate the tabletop in the most incredible ways, and then the table you made yourself will look like an expensive designer thing.

School desk options

Table for first graders should be spacious so that there is enough space for textbooks and notebooks.

For more adult student, you can purchase or make a multifunctional table with retractable panel for keyboards and with many shelves or drawers on the surface.

It is very important that workplace the child was as comfortable as possible, and all the necessary for classes things were at hand.

School tables can be completely various in appearance and design - from simple angular and straight to creative

Folding table

Table-desk

Desk for schoolchildren

We won't consider typical desks that stood in all Russian apartments in the 90s of the last century. Such tables boring in performance.

Let's consider unusual table with A-shaped legs (trests) and solid long tabletop. You can use an old one as a countertop. door canvas with a smooth surface.

Stages of work

Step 1. Draw and cut out table top. We process it with sandpaper or a grinding machine. You can make a special edging on the sides finishing edging, which is sold at any hardware store.

Note: with the edging, the width of the finished tabletop will be 72 cm!

Step 2. Cut 8 boards long no less 75 cm (if necessary, the edges will need to be trimmed with a jigsaw), sand them.

Step 3. Corner tilt boards for trestles should be such that the height of the legs in total with the thickness of the table top was 75 cm. To do this, cut out small bars, which will be located between the upper parts of the supports. The width between the lower parts should be 22 cm.

Step 4. In two boards 70 cm long drill two 9 mm holes each (for mounting the trestle). The holes should be equal distance! Above retreat about 3.5–4 cm, it all depends on the width of the board. Drill holes in the middle of the upper part of the legs 9 mm. Furniture bolts we fasten legs and strengthen the structure self-tapping screws.

Note: The bolt size is 6 mm, and the diameter of the holes for them is 9 mm! This is necessary because the table legs are attached at an angle.

Step 5. At the bottom there is a goat we fix two bars long 19 cm. The height of the fastening of the bars is not less than 3 cm from the floor. On bars we lay two boards each that will serve shelf, We fix them with self-tapping screws.

Step 6. Having measured the distance between the goats, screw it on wooden blocks to prevent the tabletop from moving.

For the best sustainability It is recommended to use countertops dowels. To do this, drill holes in the supporting boards with a depth of 8 mm, and in tabletop – 22 mm. The dowels should be dipped in glue PVA and drive into the board, then carefully place the tabletop on them. For such massive table you need to make 2-3 dowels on each side.

Step 7 All wooden parts of the table should be handle impregnation. For a children's table you need to apply no less 3 layers(so that it is impervious to moisture). Each layer should fully dry out. After the last layer has dried, the table is painted or varnished. Can be mixed with varnish a little coloring to give it the desired color shade.

Note: The table can be decorated if desired. The best decorative technique for a children's table is simply choosing a cheerful pattern or decorating the tabletop with images of the child's favorite characters.

School table for two children

Convenient and practical may be an option for two children angular table. Each child is provided with a work place and retractable drawers for storing educational supplies.
Tabletop width – 600 mm, thickness – from 16 mm.

Stages of work

Step 1. Execute sawing material or order it from a carpentry workshop.

Step 2. Collecting everything boxes. There should be 6 large ones (3 pieces for each table base) and 4 small drawers for various small items under the tabletop itself. Holes for confirmations drill using a Fostner drill. We nail hardboard to each box.

Note: confirmations can be replaced with ordinary self-tapping screws, but their connection is not so reliable.

Step 3. Using corner clamps assembling the cabinet. Fasten with self-tapping screws guides for boxes.

Step 4. We assemble the table. Tumbu and lateral We fasten the wall on top with small chipboard. Cover the part with a larger sheet rear walls. We install guides on small drawers and facades.

Step 5. In the same way we collect second the table that will longer due to two cabinets.

Step 6. We install the tabletop on short table. To do this, screw it onto small sheets.

Step 7 We attach the tabletop to second table.

Step 8 Install facades on large boxes, attach to them pens. We nail hardboard.

So that the child has comfortable work at a new desk, you should take account following:

• • Width The table for a child should be from 60 to 80 cm, length from 120 cm.
  • Boys require more workspace than girls.
  • Workplace It is recommended to organize a schoolchild near the window.
  • Definitely worth installing on a desktop lamp with bright lighting. For right-handers, the light should fall from the left, for left-handers - from the right.
  • The chair should be comfortable, it back - rigid with bending. Good decision - orthopedic armchair.
  • Screen monitor should be located during operation below eye level at an angle of 15-30 degrees.

• Color spectrum The workplace should be selected based on the child’s wishes, but you should not make it too colorful and full of poisonous colors. A tacky table can distract child from doing homework. It is enough to choose bright accessories and furniture.
• Accessories are worth choosing creative shapes: and the children's table should have its own zest. Business minimalism – not the best option for a child.

How to make a table for a schoolchild with your own hands, see video: